Technologies/components and systems

What can the Zimmer Group offer you? Over 30 years' experience for a start. Not to mention the drive to continuously improve technologies and components and develop innovations. And, of course, consistent customer focus at every level. In any industry. Anywhere in the world. Find out more.

  • 2-jaw parallel grippers

    2-Jaw Parallel Grippers

    • Stroke per jaw from 1mm ... 30 mm
    • Gripping forces up to 19000 N
    2-jaw parallel grippers
  • 2-jaw parallel grippers with long stroke

    2-Jaw Parallel Grippers with Long Stroke

    • Long strokes up to 200 mm per jaw
    • Gripping forces up to 8500 N
    2-jaw parallel grippers with long stroke
  • 3-jaw concentric grippers

    3-Jaw Concentric Grippers

    • Stroke per jaw from 1mm ... 30 mm
    • Gripping forces up to 35000 N
    3-jaw concentric grippers
  • 3-jaw concentric grippers with long stroke

    3-Jaw Concentric Grippers with Long Stroke

    • Long strokes up to 60 mm per jaw
    • Gripping forces up to 2500 N
    3-jaw concentric grippers with long stroke
  • 2-jaw angular grippers

    2-Jaw Angular Grippers

    • Opening angles up to 180°
    • High gripping torques up to 725 Nm
    2-jaw angular grippers
  • Grippers for special tasks

    Grippers for Specific Tasks

    • Special grippers for a variety of applications
    Grippers for special tasks
  • LGS series

    Series LGS Internal Grippers

    • Collet chuck can be machined
    • Possible hole diameter from 4 to 50 mm
    LGS series
  • LG1000 series
    LG1000 series
  • LGG series

    Series LGG Internal Grippers

    • Direct internal gripping via rubber knobs
    • No gripper jaw production required
    LGG series
  • RG series

    Series RG External Grippers

    • For workpiece diameters up to 58 mm
    • Automatic reset when venting
    RG series
  • ST series

    Series ST Needle Grippers

    • Adjustable stroke via scale ring from 0 to 2 mm or 1.5 mm
    • Single-acting pneumatic cylinder with spring return
    ST series
  • SCH series

    Series SCH Needle Grippers

    • Adjustable stroke by shifting the pneumatic cylinder in an elongated hole
    • Synchronized penetration by both pairs of needles
    SCH series
  • GS series

    Series GS O-Ring Assembly Grippers External

    • Expanding stroke adjustable from outside via adusting ring
    • T-Slot guide for high forces and moments capacity
    GS series
  • GSI series

    Series GSI O-Ring Assembly Grippers Internal

    • Stroke of spread jaws adjustable to fi t bore diameter of workpiece
    • Spread jaws to position the O-ring in the groove of the workpiece
    GSI series
  • HM1000 series

    Series HM1000 Magnetic Grippers

    • Integrated O-ring in contact plate to assure a secure hold of the work piece
    • The gripper is constantly ready to grip. Pressurized air should be only applied to release workpiece
    HM1000 series
  • Magnetic gripper
    Series HM1000

    Serie

    Secure hold during EMERGENCY STOP

    Magnets attached to springs ensure your workpiece remains secure, even during a drop in pressure

    Contact plate that increases friction value

    The replaceable O-ring ensures the high dynamics in your application and protection of your workpiece

    Residual holding force < 1N

    The demagnetised contact surface safeguards the process reliability of dropping off your workpiece

    Installation Size: HM1030
    Order-No.Operating pressure min.Operating pressure max.Adhesive force max.
    HM1030NC3 [bar]8 [bar]27 [N]
    Installation Size: HM1046
    Order-No.Operating pressure min.Operating pressure max.Adhesive force max.
    HM1046NC3 [bar]8 [bar]65 [N]
    Installation Size: HM1078
    Order-No.Operating pressure min.Operating pressure max.Adhesive force max.
    HM1078NC3 [bar]8 [bar]220 [N]
    Installation Size: HM1097
    Order-No.Operating pressure min.Operating pressure max.Adhesive force max.
    HM1097NC3 [bar]8 [bar]450 [N]
    Serie

    Mounting and positioning

    via centering sleeve and thread

    Spring

    for piston return

    secured holding even in drop pressure

    Permanent magnet

    requires no power supply

    high holding forces

    Transport safeguarding

    Robust, lightweight housing

    Hard-coated aluminum alloy

    single-acting pneumatic cylinders

    only one pneumatic line required

    Spring return

    Contact plate

    easy replaceable

    embedded O-ring to increase the friction coefficient